TECH SECTION A Centrifugal Pump Fundamentals	A-1 Head A-2 Capacity A-3 Power and Efficiency A-4 Specific Speed and Pump Type A-5 Net Positive Suction Head A-6 NPSH and Suction Specific Speed A-7 Pump Characteristic Curves A-8 Affinity Laws A-9 System Curves A-20 Basic Formulas and Symbols
TECH SECTION B Pump Application Guide	B-1 Corrosion and Materials of Construction B-2 Material Selection Guide and Elastomer Selection Guide B-3 Piping Design B-4A Sealing B-4B Magnetic Drive Pumps B-5 Field Testing Methods B-6 Vibration Analysis B-7 Vertical Turbine Pumps B-8 Self-Priming Pump System Guidelines B-9 Priming Time Calculations
TECH SECTION C Water Data	C-1 Friction Loss for Water — Schedule 40 Steel Pipe C-2 Resistance Coefficients for Valves and Fittings C-3 Resistance Coefficients for Increasers and Diffusers C-4 Resistance Coefficients for Reducers C-5 Properties of Water at Various Temperatures C-6 Properties of Water at Various Altitudes C-7 Steam Data — Saturation: Temperatures C-8 Steam Data — Saturation: Pressures
TECH SECTION D Properties of Liquids	D-1 Viscosity D-2 Viscosity Conversion Table D-3 Pump Performance and Viscous Liquids D-4 Viscosity Corrections Chart D-5A Viscosity of Common Liquids D-5B Physical Properties of Common Liquids D-6 Friction Loss for Viscous Liquids D-7 Pumping Liquids with Entrained Gas D-8 Solids and Slurries/Slurry Pump Application Guide D-9A,B Vapor Pressure — Various Liquids
TECH SECTION E Paper Stock	E-1 Paper Stock Discussion E-2 Conversion Chart of Mill Output in TPD E-2.1 Definition/Conversion Factors E-3 Friction Loss of Pulp Suspensions in Pipe E-4 Pump Types Used in the Pulp & Paper Industry
TECH SECTION F Mechanical Data	F-1 Standard Weights and Dimensions of Mechanical Joint Cast Iron Pipe, Centrifugally Cast F-2 Cast Iron Pipe Flanges and Flanged Fittings F-3 Steel Pipe, Dimensions and Weights F-4 Steel Pipe Flanges and Flanged Fittings F-5 150 Lb. ANSI/Metric Flange Comparison F-6 300 Lb. ANSI/Metric Flange Comparison F-7 Well Casings, Dimensions and Weights F-8 Capacities of Tanks of Various Dimensions
TECH SECTION G Motor Data	G-1 Motor Enclosures G-2 NEMA Frame Assignments G-3 NEMA Frame Dimensions G-4 Synchronous Motor Speeds G-5 Full Load Motor Current G-6 Motor Terms G-7 Electrical Conversion Formulae G-8 Vertical Motors G-9 I.E.C. Motor Frames G-10 TEFC IP55 Metric I.E.C. Motors (NEMA to metric)
TECH SECTION H Conversion Factors & Engineering Data	H-1 Temperature Conversion Chart H-2 API and Baume Gravity Tables and Weight Factors H-3 Hardness Conversion Table H-4 Miscellaneous Conversion Factors H-5 Qwik Convert Tables H-6 Conversion Chart — GPM to BPD H-7 Decimal and Millimeter Equivalents of Fractions H-8 Atmospheric Pressures and Barometer Readings
TECH SECTION I Pump Operation & Maintenance	I-1 Pump Safety Tips I-2 PRO Service Centers I-3 Symptoms and Causes of Hydraulic and Mechanical Failure I-4 Troubleshooting Centrifugal Pumps I-5 Abrasive Slurries and Pump Wear I-6 Start-up and Shut-off Procedure for Mag Drive Pumps I-7 Raised Face and Flat Face Flanges I-8 Air in Pumps I-9 Ball Bearings I-10 Impeller Clearance I-11 Predictive and Preventive Maintenance I-12 Field Alignment
TECH SECTION J Misc. Pump Information	J-1 Safe Operation of Magnetic Drive Pumps J-2 Plain Bearings Made of Silicon Carbide with Optimized Dry J-3 Centrifugal Pump Operation without NPSH Problems J-4 Suggestions for Remedies for NPSH Problems J-5 Fluoropolymers in Chemical Plant Construction